Skip to content

Free quote by phone, and a return visit once it's in: (512) 883-7067

(512) 883-7067
Technician crouched beside a tall black filter tank with a control head, plumbed next to a blue pressure tank, with a rust-stained pipe on an unfinished garage wall

ServicesIron and Sulfur Removal

Iron and Sulfur Removal in Wyldwood, TX

Orange rings in the tub and a rotten-egg smell at the tap usually have a clear cause. We test your water first and size a filter to what we find. After installation, we come back to check the results and show you how to look after it.

When an iron and sulfur filter is the right call

Dissolved iron looks clear coming out of the faucet, then turns orange or brown once it meets air. Hydrogen sulfide gives water a rotten-egg smell. Both stain fixtures, dull laundry and leave a metallic or sulfur taste in coffee and ice. A dedicated iron and sulfur filter turns these into solid particles, traps them in a media bed and flushes them away on a set schedule.

It is not always the answer. A smell that shows up only in hot water often comes from the water heater, not the supply, and we will tell you so rather than sell you a filter. That is why every job starts with a water test.

Our work does not end at startup. We return to retest, check the backwash settings and walk you through the simple care that keeps the media working well.

Technician kneels at a garage wall turning a shutoff valve beside a sediment filter, blue softener tank and brine tank as the homeowner watches

What the work includes

  1. 01

    A full water test before any quote

    We measure iron, manganese, hydrogen sulfide and pH, because each one changes which media will work. Low pH, for example, can stop some catalytic media from oxidizing iron at all.

  2. 02

    Filter media matched to your results

    Depending on the numbers, that may be an air-injection oxidizing filter, a catalytic media bed, or a chlorine-feed system with a contact tank for heavier sulfur. We explain why we chose one over the others.

  3. 03

    Careful, serviceable installation

    We place the tank where it can be reached for service, add a bypass valve so the system can be isolated, and route the backwash line to a proper drain. Floors are covered, and the work area is left clean.

  4. 04

    Free installation

    Free installation is part of our offer. Your written quote lists the equipment and any extra plumbing parts line by line.

  5. 05

    Follow-up visit and retest

    A few weeks after startup we come back, test the water at your tap again and adjust the backwash timing if needed. You also get a short care sheet written for your specific system.

Questions about Iron and Sulfur Removal?

Call(512) 883-7067

Signs your water needs iron and sulfur removal

  • Orange or brown stains

    Rust-colored rings in toilets, sinks and showers that return within days of scrubbing point to dissolved iron.

  • A rotten-egg smell

    A sulfur odor at both hot and cold taps suggests hydrogen sulfide in the supply. If it is only on the hot side, we look at the water heater first.

  • Dingy or spotted laundry

    Whites that yellow or pick up rust spots are a common clue. Chlorine bleach makes it worse, because it oxidizes the iron straight onto the fabric.

  • Slime in the toilet tank

    A reddish or gray gel on the tank walls is often iron or sulfur bacteria. It feeds on the same minerals and can clog aerators and fill valves over time.

  • Black specks or tarnished fixtures

    Dark staining and quick tarnish on silverware or brass can come from manganese or sulfur, which often travel with iron.

How an installation day runs

  1. 1

    Test and talk it through

    We test at your tap, share the numbers and recommend a system sized to your iron and sulfur levels and how much water your home uses. You have the quote before anything is booked.

  2. 2

    Prepare the space

    On the day, we protect the floors, shut off the water at the main and confirm a drain and outlet are within reach for the backwash cycle. Your water is off for only part of the visit.

  3. 3

    Install and start up

    We plumb in the tank with its bypass, load and rinse the media, and run a first backwash to clear fine particles. Then we program the control valve for your water and set the cleaning cycle for overnight.

  4. 4

    Check back and show you the care

    We return a few weeks later to retest and fine-tune. We show you how to read the control valve, when to put the system in bypass, and which changes in smell or color mean it is time to give us a ring.

What affects the cost

Iron and sulfur systems are priced by what your water needs, not as a fixed package. Since installation is free, your quote comes down to the equipment and any plumbing changes. Once testing is done, we list every part so nothing appears later.

Iron and sulfur levels
Higher concentrations call for a larger media bed or a chlorine-feed system with a contact tank, which costs more than a single air-injection tank.
The rest of your water chemistry
Low pH, manganese or tannins may need an extra stage, such as a pH neutralizer or a sediment pre-filter ahead of the main tank.
Flow rate and household size
A home with several bathrooms needs a tank large enough to hold steady pressure while showers and appliances run at the same time.
Where the system goes
A garage or utility room near the main and a drain is simplest. Longer backwash lines or a hard-to-reach main add plumbing materials, and those appear on the quote.

Iron and sulfur removal questions

Will a water softener remove iron?

A softener can handle small amounts of dissolved iron, but heavier iron fouls the resin and sulfur passes straight through. If your water is also hard, we may place an iron filter ahead of a softener. Our Water Softener Installation page covers that side of it.

How much upkeep does an iron filter need?

Very little day to day. The system backwashes itself on a timer and sends trapped iron down the drain. Chlorine-feed systems need the solution tank topped up, and the media is replaced every several years depending on your water. We go through all of it at the follow-up visit.

Why does my water smell only at the hot taps?

That pattern usually points to the water heater. Bacteria in the tank can react with the magnesium anode rod and produce hydrogen sulfide. A different anode or a tank flush often fixes it, and we will tell you that rather than install a filter you do not need.

Will a filter remove the stains already on my fixtures?

It stops new staining, but existing stains need cleaning with an iron-specific cleaner. We can suggest products that are gentle on your fixture finishes. Once the source is filtered, the stains stop coming back.

Does the water test cost anything?

No. The water test is free, and installation is free if you choose a system. You get the results and a quote by phone before you decide anything.

Find out what is in your water first

One phone call books a free water test and a quote built on the results. Once the system is running, we come back to check the water and show you how to care for it.